Installation
INSTALLATION
CAUTION / NOTICE / HINT
PROCEDURE
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
(a) Install the front seat belt anchor plate as shown in the illustration.
 |
Install in this Direction |
(b) Install the front seat inner belt assembly LH with the nut.
 |
Protruding Part |
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do
not allow the anchor part of the front seat inner belt assembly LH to
overlap the protruding part of the separate type front seat cushion
spring assembly.
(c) Engage each clamp.
(d) Connect each connector.
2. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
(a) Install the front seat belt anchor plate as shown in the illustration.
|
|
Install in this Direction |
(b) Install the front seat inner belt assembly RH with the nut.
|
|
Protruding Part |
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do
not allow the anchor part of the front seat inner belt assembly RH to
overlap the protruding part of the separate type front seat cushion
spring assembly.
(c) Engage each clamp.
(d) Connect each connector.
3. INSTALL FRONT SEAT ASSEMBLY
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during front seat inner belt assembly
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
|
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
|
Front passenger seat | Zero point calibration (Occupant classification system) |
- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
|
|
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY
Click here
2. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
(a) Disconnect each connector.
(b) Disengage each clamp.
| (c) Remove the nut and front seat inner belt assembly LH. |
|
(d) Remove the front seat belt anchor plate as shown in the illustration.
 |
Remove in this Direction |
3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
(a) Disconnect each connector.
(b) Disengage each clamp.
| (c) Remove the nut and front seat inner belt assembly RH. |
|
(d) Remove the front seat belt anchor plate as shown in the illustration.
|
|
Remove in this Direction |
