Components
COMPONENTS
ILLUSTRATION
|
*A | w/ Seat Position Memory System |
- | - |
|
*1 | POSITION CONTROL ECU ASSEMBLY |
*2 | SEAT POSITION AIRBAG SENSOR |
|
*3 | SEAT SLIDE POSITION SENSOR PROTECTOR |
- | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
- | - |
Installation
INSTALLATION
PROCEDURE
1. INSTALL SEAT POSITION AIRBAG SENSOR
(a)
Engage the pin to install the seat position airbag sensor to the seat
slide position sensor protector as shown in the illustration.
 |
Install in this Direction |
| (b) Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position airbag sensor with the "TORX" bolt.
NOTICE:
- If the seat position airbag sensor has been dropped, or there are any
cracks, dents or other defects in the case or connector, replace the
seat position airbag sensor with a new one.
- When installing the seat position airbag sensor, make sure that the SRS
wiring does not interfere with or is pinched between other parts.
|
 |
|
*1 | Seat Position Airbag Sensor | |
*a | Feeler Gauge | |
*b | 1.3 mm (0.0512 in.) | |
*c | Seat Rail | | |
(c) Using a T30 "TORX" socket wrench, tighten the "TORX" bolt.
Torque:
8.0 N·m {82 kgf·cm, 71 in·lbf}
(d) Make sure that the clearance between the seat position airbag sensor and seat rail is 1.3 mm (0.0512 in.).
(e) Connect the connector and engage the clamp.
(f) Check that there is no looseness in the installed parts of the seat position airbag sensor.
2. INSTALL POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
Click here 
3. INSTALL FRONT SEAT ASSEMBLY LH
Click here
4. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here
for HV Model: Click here
On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
CAUTION:
Be sure to correctly follow the removal and installation procedures for the seat position airbag sensor.
PROCEDURE
1. INSPECT SEAT POSITION AIRBAG SENSOR (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check.
for Gasoline Model: Click here
for HV Model: Click here
2. INSPECT SEAT POSITION AIRBAG SENSOR (for Vehicle Involved in Collision)
(a) Perform a diagnostic system check.
for Gasoline Model: Click here
for HV Model: Click here
(b) Visually check for defects with the seat position airbag sensor removed from the vehicle.
HINT:
The defects are as follows:
- Cracks in the sensor housing
- Dents in the sensor housing
- Chips in the sensor housing
- Cracks or other damage to the connector
OK:
No defects are found.
If any defects are found, replace the seat position airbag sensor with a new one.
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization or
registration) that must be performed after parts are removed and
installed, or replaced during seat position airbag sensor
removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
|
Pre-collision System |
|
Intelligent Clearance Sonar System* |
|
Lighting System (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
Panoramic View Monitor System |
|
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
Click here
2. REMOVE POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
Click here
3. REMOVE SEAT POSITION AIRBAG SENSOR
| (a) Disengage the clamp and disconnect the connector. | |
| (b)
Using a T30 "TORX" socket wrench, remove the "TORX" bolt and seat
position airbag sensor with the seat slide position sensor protector. |
|
(c)
Disengage the pin to remove the seat position airbag sensor from the
seat slide position sensor protector as shown in the illustration.
 |
Remove in this Direction |
