Toyota Avalon (XX50): Combination Meter

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Interior / Meter / Gauge / Display / Combination Meter

Components

COMPONENTS

ILLUSTRATION

*1	CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY	*2	CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
*3	CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL	*4	CONSOLE BOX BEZEL
*5	CONSOLE BOX POCKET SUB-ASSEMBLY	*6	FRONT CONSOLE UPPER PANEL GARNISH
*7	LOWER INSTRUMENT PANEL FINISH PANEL LH	*8	LOWER INSTRUMENT PANEL FINISH PANEL RH
*9	LOWER INSTRUMENT PANEL SUB-ASSEMBLY	*10	RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
*11	REAR UPPER CONSOLE PANEL SUB-ASSEMBLY	*12	SHIFT LEVER KNOB SUB-ASSEMBLY

ILLUSTRATION

*1	COMBINATION METER ASSEMBLY	*2	COMBINATION METER GLASS
*3	INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY	*4	INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
*5	LOWER CENTER INSTRUMENT PANEL FINISH PANEL	*6	LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
*7	LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL	*8	NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Disassembly

DISASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

When removing and installing the combination meter glass, make sure not to touch the display panel.
Do not allow any dirt, fingerprints, grease, etc., to adhere to the combination meter glass. If the glass is dirty, wipe it clean with a soft cloth.

PROCEDURE

1. REMOVE COMBINATION METER GLASS

(a) Disengage the 8 claws to remove the combination meter glass.

Installation

INSTALLATION

PROCEDURE

1. INSTALL COMBINATION METER ASSEMBLY

(a) Connect the 2 connectors.

(b) Engage the clamp.

Install in this Direction

(d) Install the combination meter assembly with the 3 screws.

2. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Click here

4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Click here

5. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Click here

6. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

7. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Click here

8. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Click here

9. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Click here

10. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL

Click here

11. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Click here

12. INSTALL CONSOLE BOX BEZEL

Click here

13. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY

Click here

14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Click here

15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

16. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY

Click here

17. INSTALL FRONT CONSOLE UPPER PANEL GARNISH

Click here

18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH

Click here

19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

Click here

20. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

21. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)

Click here

Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

When removing and installing the combination meter glass, make sure not to touch the display panel.
Do not allow any dirt, fingerprints, grease, etc., to adhere to the combination meter glass. If the glass is dirty, wipe it clean with a soft cloth.

PROCEDURE

1. INSTALL COMBINATION METER GLASS

(a) Engage the 8 claws to install the combination meter glass.

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

Click here

3. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH

Click here

5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH

Click here

6. REMOVE FRONT CONSOLE UPPER PANEL GARNISH

Click here

7. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY

Click here

8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Click here

10. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY

Click here

11. REMOVE CONSOLE BOX BEZEL

Click here

12. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Click here

13. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL

Click here

14. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Click here

15. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Click here

16. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Click here

17. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

18. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Click here

19. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Click here

20. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Click here

21. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

22. REMOVE COMBINATION METER ASSEMBLY

(a) Remove the 3 screws.

(b) Disengage the 2 clips as shown in the illustration.

Remove in this Direction

(d) Disconnect the 2 connectors to remove the combination meter assembly.

Vanity Light

Headup Display System(for Gasoline Model)

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Can Communication System(for Hv Model): Check Bus 5 Line for Short to GND
DESCRIPTION There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and termin ...