Components
COMPONENTS
ILLUSTRATION
|
*A | for HV Model |
- | - |
|
*1 | LUGGAGE TRIM SERVICE HOLE COVER |
- | - |
ILLUSTRATION
|
*A | w/ Seat Heater System |
- | - |
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
|
*A | for Gasoline Model |
*B | for HV Model |
|
*C | w/ Seat Heater System |
- | - |
|
*1 | LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
|
*3 | REAR SEAT CUSHION ASSEMBLY |
*4 | REAR SEAT CUSHION LOCK HOOK |
|
*5 | REAR SIDE SEATBACK ASSEMBLY LH |
*6 | REAR SIDE SEATBACK ASSEMBLY RH |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
ILLUSTRATION
|
*1 | PACKAGE TRAY TRIM PANEL ASSEMBLY |
*2 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
|
*3 | REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*4 | REAR DOOR OPENING TRIM WEATHERSTRIP RH |
|
*5 | REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH |
*6 | REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH |
|
*7 | REAR SEAT BELT RETRACTOR COVER |
*8 | REAR SEAT SHOULDER BELT COVER |
|
*9 | ROOF SIDE INNER GARNISH LH |
*10 | ROOF SIDE INNER GARNISH RH |
|
*11 | ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*12 | ROOF SIDE RAIL GARNISH ASSEMBLY RH |
|
*13 | CLIP |
- | - |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
|
● | Non-reusable part |
- | - |
Inspection
INSPECTION
PROCEDURE
1. INSPECT REAR CENTER SEAT OUTER BELT ASSEMBLY
| (a) Before installing the rear center seat outer belt assembly, check the ELR function.
NOTICE: Do not disassemble the retractor. (1)
When the inclination of the retractor is 15° or less, check that the
belt can be pulled from the retractor. When the inclination of the
retractor is over 45°, check that the belt locks. If the result is not as specified, replace the rear center seat outer belt assembly. |
 |
|
*a | Retractor | |
*b | Unlock | |
*c | Lock | |
*d | 45° | | |
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR SEAT BELT RETRACTOR COVER
(a) Install the seat belt retractor cover as shown in the illustration.
 |
Install in this Direction |
2. INSPECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here 
3. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
| (a) Engage the guide and temporarily install the rear center seat outer belt assembly with the 2 bolts. |
|
(b) Fully tighten the bolt (A), and then the bolt (B) to install the rear center seat outer belt assembly.
Torque:
Bolt (A) :
12.5 N·m {127 kgf·cm, 9 ft·lbf}
Bolt (B) :
42 N·m {428 kgf·cm, 31 ft·lbf}
(c) Check that the ELR locks.
NOTICE:
This check should be performed with the rear center seat outer belt assembly installed to the vehicle.
(1)
With the rear center seat outer belt assembly installed to the vehicle,
check that the belt locks when it is pulled out quickly.
4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
5. INSTALL REAR SEAT SHOULDER BELT COVER
Click here
6. INSTALL CENTER STOP LIGHT SET
Click here
7. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
8. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
9. INSTALL ROOF SIDE INNER GARNISH LH
Click here
10. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
11. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
12. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
13. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
14. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here
15. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
Click here
16. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
17. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
18. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here
19. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
21. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here
22. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here
23. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
24. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model:
Click here
for Gasoline Model:
Click here
25. INSPECT SRS WARNING LIGHT
for HV Model:
Click here
for Gasoline Model:
Click here
On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION / NOTICE / HINT
CAUTION:
Be sure to correctly follow the removal and installation procedures for the rear center seat outer belt assembly.
PROCEDURE
1. INSPECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Vehicle not Involved in Collision)
(a) Visually check for defects with the rear center seat outer belt assembly installed to the vehicle.
(1) The defects to be checked are as follows:
- Cuts on the rear center seat outer belt assembly
- Small cracks on the rear center seat outer belt assembly
- Significant discoloration on the rear center seat outer belt assembly
OK:
No defects are found.
HINT:
If any defects are found, replace the rear center seat outer belt assembly with a new one.
2. INSPECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Vehicle Involved in Collision)
(a) Visually check for defects with the rear center seat outer belt assembly removed from the vehicle.
(1) The defects to be checked are as follows:
- Cuts on the rear center seat outer belt assembly
- Small cracks on the rear center seat outer belt assembly
- Significant discoloration on the rear center seat outer belt assembly
- Cracks or other damage on the connector
OK:
No defects are found.
HINT:
If any defects are found, replace the rear center seat outer belt assembly with a new one.
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization or
registration) that must be performed after parts are removed and
installed, or replaced during rear center seat outer belt assembly
removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
CAUTION:
- Be sure to read Precaution thoroughly before servicing.
Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
CAUTION:
- Be sure to read Precaution thoroughly before servicing.
Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here
4. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here
5. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
(b) Disengage the guide to remove the rear center seat outer belt assembly.
6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative
(-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
8. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
9. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
10. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here
11. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here
15. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
16. REMOVE ROOF SIDE INNER GARNISH LH
Click here
17. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
18. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here
19. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
20. REMOVE CENTER STOP LIGHT SET
Click here
21. REMOVE REAR SEAT SHOULDER BELT COVER
Click here
22. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
23. REMOVE REAR SEAT BELT RETRACTOR COVER
(a) Remove the seat belt retractor cover as shown in the illustration.
 |
Remove in this Direction |
