Components
COMPONENTS
ILLUSTRATION
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
|
*A | for Gasoline Model |
*B | for HV Model |
|
*1 | LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
|
*3 | REAR SEAT CUSHION ASSEMBLY |
*4 | REAR SEAT CUSHION LOCK HOOK |
|
*5 | REAR SEAT HEADREST ASSEMBLY |
*6 | REAR SEAT INNER BELT ASSEMBLY LH |
|
*7 | REAR SEATBACK ASSEMBLY LH |
*8 | REAR SEATBACK ASSEMBLY RH |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
Inspection
INSPECTION
PROCEDURE
1. INSPECT REAR SEAT INNER BELT ASSEMBLY LH (for Gasoline Model)
(a) Inspect the rear seat inner with center belt assembly LH (for LH).
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
4 - 3 | Rear LH seat belt unfastened |
Below 1 Ω | If the result is not as specified, replace the rear seat inner with center belt assembly LH. |
 |
|
*a | Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH (for LH)) | | |
(b) Inspect the rear seat inner with center belt assembly LH (for center).
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
1 - 2 | Rear center seat belt unfastened |
Below 1 Ω | If the result is not as specified, replace the rear seat inner with center belt assembly LH. |
|
|
|
*a | Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH (for Center)) | | |
2. INSPECT REAR SEAT INNER BELT ASSEMBLY LH (for HV Model)
(a) Inspect the rear seat inner with center belt assembly LH (for LH).
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
5 - 4 | Rear LH seat belt unfastened |
Below 1 Ω | If the result is not as specified, replace the rear seat inner with center belt assembly LH. |
 |
|
*a | Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH (for LH)) | | |
(b) Inspect the rear seat inner with center belt assembly LH (for center).
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
1 - 2 | Rear center seat belt unfastened |
Below 1 Ω | If the result is not as specified, replace the rear seat inner with center belt assembly LH. |
|
|
|
*a | Component without harness connected
(Rear Seat Inner with Center Belt Assembly LH (for Center)) | | |
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR SEAT INNER BELT ASSEMBLY LH
(a) Install the rear seat inner with center belt assembly LH with the bolt.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do
not allow the anchor part of the rear seat inner with center belt
assembly LH to overlap the protruding parts of the vehicle body.
 |
Protruding Part |
(b) Engage the clamp.
(c) Connect the connector.
2. INSTALL REAR SEATBACK ASSEMBLY RH
Click here 
3. INSTALL REAR SEATBACK ASSEMBLY LH
Click here
4. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
5. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here
6. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
7. INSTALL REAR SEAT HEADREST ASSEMBLY
Click here
8. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
9. INSTALL SPARE WHEEL COVER ASSEMBLY
Click here
Removal
REMOVAL
PROCEDURE
1. REMOVE SPARE WHEEL COVER ASSEMBLY
Click here 
2. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
3. REMOVE REAR SEAT HEADREST ASSEMBLY
Click here
4. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
5. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
6. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
7. REMOVE REAR SEATBACK ASSEMBLY LH
Click here
8. REMOVE REAR SEATBACK ASSEMBLY RH
Click here
9. REMOVE REAR SEAT INNER BELT ASSEMBLY LH
| (a) Disconnect the connector. | |
(b) Disengage the clamp.
(c) Remove the bolt and rear seat inner with center belt assembly LH.
HINT:
The bolt cannot be removed from the rear seat inner with center belt assembly LH.
