Installation
INSTALLATION
PROCEDURE
1. INSTALL ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.
- If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(a) Connect the connector.
(b) Engage the 2 guides and install the electrical key and tire pressure warning ECU and receiver with the bolt.
Torque:
8.3 N·m {85 kgf·cm, 73 in·lbf}
2. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
3. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here
5. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
6. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
7. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here
8. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
10. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here
11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here
12. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
13. REGISTER TRANSMITTER ID
for Gasoline Model:
Click here
for HV Model:
Click here
14. INSPECT TIRE PRESSURE WARNING SYSTEM
for Gasoline Model:
Click here
for HV Model:
Click here
15. PERFORM INITIALIZATION
for Gasoline Model:
Click here
for HV Model:
Click here
16. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model:
Click here
for HV Model:
Click here
17. INSPECT SRS WARNING LIGHT
for Gasoline Model:
Click here
for HV Model:
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
The
necessary procedures (adjustment, calibration, initialization, or
registration) that must be performed after parts are removed and
installed, or replaced during electrical key and tire pressure warning
ECU and receiver removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here  |
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for Gasoline Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
|
Electrical key and tire pressure warning ECU and receiver |
- Register transmitter ID
- Initialize tire pressure warning system
|
- When DTC detection conditions of "transmitter ID not received" DTC are
met, TPWS indicator blinks for 1 minute, and then illuminates.
- Tire pressure warning function
|
for Registration
for Initialization |
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
NOTICE:
When
replacing the electrical key and tire pressure warning ECU and
receiver, read the transmitter IDs stored in the old ECU using the
Techstream and write them down before removal.
Click here
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model) |
Replaced Part or Performed Procedure |
Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|
*: When performing learning using the Techstream.
Click here |
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|
Intelligent clearance sonar system* |
|
Lighting system (for HV Model with Cornering Light) |
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
Panoramic view monitor system |
|
|
Electrical key and tire pressure warning ECU and receiver |
- Register transmitter ID
- Initialize tire pressure warning system
|
- When DTC detection conditions of "transmitter ID not received" DTC are
met, TPWS indicator blinks for 1 minute, and then illuminates.
- Tire pressure warning function
|
for Registration
for Initialization |
CAUTION:
Some
of these service operations affect the SRS airbag system. Read the
precautionary notices concerning the SRS airbag system before servicing.
Click here
NOTICE:
When
replacing the electrical key and tire pressure warning ECU and
receiver, read the transmitter IDs stored in the old ECU using the
Techstream and write them down before removal.
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After
turning the engine switch (for Gasoline Model) or power switch (for HV
Model) off, waiting time may be required before disconnecting the cable
from the negative (-) auxiliary battery terminal. Therefore, make sure
to read the disconnecting the cable from the negative (-) auxiliary
battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here
3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here
4. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here
for 2GR-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative
(-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
Click here
11. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
12. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
13. REMOVE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.
- If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(b) Disengage the 2 guides.
(c) Disconnect the connector to remove the electrical key and tire pressure warning ECU and receiver.
