Toyota Avalon (XX50): Roof Headlining

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Interior / Interior Panels / Trim / Roof Headlining

Components

COMPONENTS

ILLUSTRATION

*A	w/o Front No. 3 Speaker	*B	w/ Front No. 3 Speaker
*C	for Gasoline Model	*D	for HV Model
*1	CENTER PILLAR LOWER GARNISH LH	*2	CENTER PILLAR UPPER GARNISH LH
*3	COWL SIDE TRIM SUB-ASSEMBLY LH	*4	FRONT DOOR OPENING TRIM WEATHERSTRIP LH
*5	FRONT DOOR SCUFF PLATE LH	*6	FRONT PILLAR GARNISH LH
*7	FRONT SEAT OUTER BELT ASSEMBLY LH	*8	LAP BELT OUTER ANCHOR COVER
*9	REAR DOOR OPENING TRIM WEATHERSTRIP LH	*10	REAR DOOR SCUFF PLATE LH
*11	ROOF SIDE INNER GARNISH LH	*12	ROOF SIDE RAIL GARNISH ASSEMBLY LH
*13	CLIP	*14	FRONT PILLAR GARNISH CLIP
	Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": Nm (kgfcm, ft.*lbf)	●	Non-reusable part

ILLUSTRATION

*A	w/o Front No. 3 Speaker	*B	w/ Front No. 3 Speaker
*C	for Gasoline Model	*D	for HV Model
*1	CENTER PILLAR LOWER GARNISH RH	*2	CENTER PILLAR UPPER GARNISH RH
*3	COWL SIDE TRIM SUB-ASSEMBLY RH	*4	FRONT DOOR OPENING TRIM WEATHERSTRIP RH
*5	FRONT DOOR SCUFF PLATE RH	*6	FRONT PILLAR GARNISH RH
*7	FRONT SEAT OUTER BELT ASSEMBLY RH	*8	LAP BELT OUTER ANCHOR COVER
*9	REAR DOOR OPENING TRIM WEATHERSTRIP RH	*10	REAR DOOR SCUFF PLATE RH
*11	ROOF SIDE INNER GARNISH RH	*12	ROOF SIDE RAIL GARNISH ASSEMBLY RH
*13	CLIP	*14	FRONT PILLAR GARNISH CLIP
	Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": Nm (kgfcm, ft.*lbf)	●	Non-reusable part

ILLUSTRATION

*A	for Normal Roof	*B	for Moon Roof
*C	w/ Humidity Sensor	-	-
*1	AIR CONDITIONING THERMISTOR ASSEMBLY	*2	NO. 1 FORWARD RECOGNITION COVER
*3	NO. 2 FORWARD RECOGNITION COVER	*4	ROOF CONSOLE BOX ASSEMBLY
*5	SENSOR COVER	*6	SPOT LIGHT ASSEMBLY

ILLUSTRATION

*A	for Moon Roof	-	-
*1	ASSIST GRIP SUB-ASSEMBLY	*2	REAR ASSIST GRIP ASSEMBLY LH
*3	REAR ASSIST GRIP ASSEMBLY RH	*4	SUN ROOF OPENING TRIM MOULDING
*5	VISOR ASSEMBLY LH	*6	VISOR ASSEMBLY RH
*7	VISOR BRACKET COVER LH	*8	VISOR BRACKET COVER RH
*9	VISOR HOLDER LH	*10	VISOR HOLDER RH
*11	ASSIST GRIP COVER LH	*12	ASSIST GRIP COVER RH

ILLUSTRATION

*A	for Normal Roof	*B	for Moon Roof
*1	ROOF HEADLINING ASSEMBLY	*2	CLIP

ILLUSTRATION

*A	for Normal Roof	-	-
*1	NO. 1 ROOF WIRE	*2	NO. 2 ROOF SILENCER
*3	NO. 3 ANTENNA CORD SUB-ASSEMBLY	*4	ROOF HEADLINING

ILLUSTRATION

*A	for Moon Roof	*B	w/ Active Noise Control System
*1	ACTIVE NOISE CONTROL MICROPHONE WITH COVER	*2	NO. 1 ROOF WIRE
*3	NO. 3 ANTENNA CORD SUB-ASSEMBLY	*4	ROOF HEADLINING

Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE NO. 2 ROOF SILENCER (for Normal Roof)

(a) Remove the 2 No. 2 roof silencers.

2. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click here

3. REMOVE ACTIVE NOISE CONTROL MICROPHONE WITH COVER (w/ Active Noise Control System)

Click here

4. REMOVE NO. 1 ROOF WIRE

(a) Remove the adhesive tape from the roof headlining assembly.

*A	for Normal Roof	*B	for Moon Roof
*C	w/ Active Noise Control System	-	-
	Adhesive Tape	-	-

(b) Disengage the No. 1 roof wire from each notch.

*A	for Normal Roof	*B	for Moon Roof
*C	w/ Humidity Sensor	-	-
*a	Notch	-	-

Installation

INSTALLATION

PROCEDURE

1. INSTALL ROOF HEADLINING ASSEMBLY

(a) Install the 4 clips to the roof headlining assembly.

*a	Clip (Black)
*b	Clip (White)

(b) Put the roof headlining assembly into the vehicle through the front door RH as shown in the illustration.

Install in this Direction

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(1) Engage the 2 claws to install the base of each visor holder.

Base of Visor Holder

(2) Engage the 4 clips and install the roof headlining assembly.

(d) for Roof Side (for Moon Roof):

(1) Engage the 2 claws to install the base of each visor holder.

Base of Visor Holder

(2) Engage the 4 clips and install the roof headlining assembly.

(3) Connect the connector.

(e) for Rear Pillar LH Side:

(1) Engage the guide.

(2) Connect the connector.

(f) for Rear Pillar RH Side:

(1) Engage the guide.

(2) Connect each connector.

(g) for Front Pillar LH Side:

(1) Remove the protective cover.

(2) Engage the 4 clamps.

(3) Connect the 2 connectors.

(4) Install the protective cover.

(h) for Front Pillar RH Side:

(1) Remove the protective cover.

(2) Engage the 2 clamps.

(3) Engage the guide.

(4) Connect the connector bracket with the bolt.

(5) Install the protective cover.

(i) for Windshield Glass Side:

(1) Connect each connector.

2. INSTALL SUN ROOF OPENING TRIM MOULDING (for Moon Roof)

(a) Align the alignment tape on the sun roof opening trim moulding with the notch of the roof headlining assembly and install the sun roof opening trim moulding.

NOTICE:

After installation, check that the corners fit correctly.

*a	Alignment Tape
*b	Notch

3. INSTALL VISOR HOLDER LH

(a) Install the visor holder LH as shown in the illustration.

Install in this Direction

4. INSTALL VISOR ASSEMBLY LH

NOTICE:

Make sure to install the visor assembly LH with its arrow facing the front of the vehicle.

(a) Connect the connector.

(b) Connect the visor assembly LH to the visor holder LH.

*1	Visor Holder LH

(1) Using a T25 "TORX" socket wrench, install the visor assembly LH with the 2 screws.

(d) except "TORX" Screw:

(1) Install the visor assembly LH with the 2 screws.

5. INSTALL VISOR BRACKET COVER LH

(a) Engage the 4 claws to install the visor bracket cover LH.

6. INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.

7. INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

8. INSTALL VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.

9. INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip sub-assemblies.

(a) Install the 2 clips to the assist grip.

(b) Temporarily install the 2 assist grip covers to the assist grip as shown in the illustration.

Install in this Direction

(d) Engage the 4 claws to install the assist grip cover LH and assist grip cover RH.

NOTICE:

Make sure that the clip is engaged securely.

*1	Assist Grip Cover LH
*2	Assist Grip Cover RH

10. INSTALL REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip sub-assembly.

11. INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip sub-assembly.

12. INSTALL NO. 1 FORWARD RECOGNITION COVER

Click here

13. INSTALL NO. 2 FORWARD RECOGNITION COVER

Click here

14. INSTALL AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Click here

15. INSTALL SENSOR COVER (w/ Humidity Sensor)

Click here

16. INSTALL SPOT LIGHT ASSEMBLY

Click here

17. INSTALL ROOF CONSOLE BOX ASSEMBLY

Click here

18. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

for UA80E: Click here

for P710: Click here

19. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

20. INSTALL ROOF SIDE INNER GARNISH LH

(a) Install 3 new clips to the roof side inner garnish LH.

(b) Engage the guide as shown in the illustration.

Install in this Direction

21. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

(a) Engage the 3 guides and 3 claws as indicated by the arrows, in the order shown in the illustration to install the roof side rail garnish assembly LH.

	Install in this Direction (1)
	Install in this Direction (2)

22. INSTALL CENTER PILLAR UPPER GARNISH LH

(a) Install a new clip to the center pillar upper garnish LH.

(b) Engage the 3 guides and clip as shown in the illustration.

Install in this Direction

23. INSTALL CENTER PILLAR LOWER GARNISH LH

(a) Engage the 2 claws and 3 clips to install the center pillar lower garnish LH as shown in the illustration.

Install in this Direction

24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

25. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here

26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

27. INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)

(a) Engage the guide and 6 claws to install the rear door scuff plate LH as shown in the illustration.

Install in this Direction

28. INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)

(a) Engage the guide, 6 claws and clip to install the rear door scuff plate LH as shown in the illustration.

Install in this Direction

29. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.

(b) Install 2 new front pillar garnish clips to the front pillar garnish LH.

HINT:

Make sure that the front pillar garnish clip is engaged correctly.

*1	Front Pillar Garnish Clip
*2	Front Pillar Garnish LH

(1) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.

Install in this Direction

(d) w/ Front No. 3 Speaker:

(1) Connect the connector.

(2) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.

(e) Engage the 2 front pillar garnish clips to install the front pillar garnish LH as shown in the illustration.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.

*1	Front Pillar Garnish Clip
	Install in this Direction

30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the claw and clip as shown in the illustration.

Install in this Direction

(b) Install the cowl side trim sub-assembly LH with the clip.

32. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the guide and 10 claws to install the front door scuff plate LH as shown in the illustration.

Install in this Direction

33. INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

34. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

35. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.

36. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

37. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

38. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

40. INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

41. INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

43. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

44. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

45. INSTALL REAR SEAT ASSEMBLY

Click here

46. INSTALL FRONT SEAT ASSEMBLY

Click here

Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL NO. 1 ROOF WIRE

(a) for Normal Roof:

Apply butyl tape as shown in the illustration.

*a

Marking

-

-

Butyl Tape

-

-

NOTICE:

Securely attach the butyl tape.

(b) for Moon Roof:

Apply butyl tape as shown in the illustration.

*A	w/o Active Noise Control System	*B	w/ Active Noise Control System
*a	Marking	-	-
	Butyl Tape	-	-

NOTICE:

Securely attach the butyl tape.

*A	for Normal Roof	*B	for Moon Roof
*C	w/ Humidity Sensor	-	-
*a	Marking Tape (A)	*b	Marking Tape (B)
*c	Notch	*d	Marking
	Adjustment Area	-	-

(d) Engage each clamp.

(e) Engage the No. 1 roof wire to each notch of the roof headlining as shown in the illustration.

(f) Align the marking tape (B) on the No. 1 roof wire with the markings on the roof headlining.

(g) Attach the No. 1 roof wire with the butyl tape.

NOTICE:

Securely attach the No. 1 roof wire.
If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.
Make sure to attach the No. 1 roof wire without leaving any of it loose.

HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.

(h) Install the No. 1 roof wire to the roof headlining with adhesive tape.

*A	for Normal Roof	*B	for Moon Roof
*C	w/ Active Noise Control System	-	-
*1	No. 1 Roof Wire	-	-
*a	Correct	*b	Incorrect
*c	Marking	*d	10 mm (0.394 in.) or more
	Adhesive Tape	-	-

Adhesive Tape Size

Area	Dimension	Area	Dimension
A	20 mm (0.787 in.)	B	80 mm (3.15 in.) or more

NOTICE:

Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

2. INSTALL ACTIVE NOISE CONTROL MICROPHONE WITH COVER (w/ Active Noise Control System)

Click here

3. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click here

4. INSTALL NO. 2 ROOF SILENCER (for Normal Roof)

(a) Align the 2 No. 2 roof silencers with the markings on the roof headlining and install them using hot-melt glue as shown in the illustration.

Hot-melt Glue

Marking

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Front passenger seat	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) auxiliary battery terminal	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Front passenger seat	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for Gasoline Model: Click here

for HV Model: Click here

PROCEDURE

1. REMOVE FRONT SEAT ASSEMBLY

Click here

2. REMOVE REAR SEAT ASSEMBLY

Click here

3. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the claw as shown in the illustration.

	Place Hand Here
	Remove in this Direction

HINT:

Use the same procedure for the front side and rear side.

(b) Disengage the 8 claws and guide to remove the front door scuff plate LH as shown in the illustration.

Remove in this Direction

4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Remove the clip.

Remove in this Direction

(b) Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.

5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

6. REMOVE FRONT PILLAR GARNISH LH

(a) Apply protective tape around the front pillar garnish LH as shown in the illustration.

Protective Tape

(b) Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the front pillar garnish clip.

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.

*1	Front Pillar Garnish Clip
	Remove in this Direction

*1	Front Pillar Garnish Clip

HINT:

When the front pillar garnish clip cannot be disengaged easily:

While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

Move in this Direction
While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

Pull in this Direction

(d) Disengage the front pillar garnish LH from the base of the front pillar garnish clip as shown in the illustration.

*1	Front Pillar Garnish Clip
	Remove in this Direction

(e) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

*1	Front Pillar Garnish Clip
	Remove in this Direction

HINT:

When the front pillar garnish clip cannot be disengaged easily:

While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

Move in this Direction
While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

Pull in this Direction

(f) w/o Front No. 3 Speaker:

(1) Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.

Remove in this Direction

(g) w/ Front No. 3 Speaker:

(1) Disengage the 2 guides as shown in the illustration.

(2) Disconnect the connector to remove the front pillar garnish LH.

(h) Remove the 2 front pillar garnish clips from the front pillar garnish LH.

(i) Protect the curtain shield airbag assembly LH.

(1) Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

*1	Curtain Shield Airbag Assembly LH
*a	Protective Cover
*b	Adhesive Tape

7. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)

(a) Disengage the claw as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disengage the 5 claws and guide to remove the rear door scuff plate LH as shown in the illustration.

Remove in this Direction

8. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)

(a) Disengage the claw as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disengage the 5 claws, clip and guide to remove the rear door scuff plate LH as shown in the illustration.

Remove in this Direction

9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

10. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here

11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

12. REMOVE CENTER PILLAR LOWER GARNISH LH

(a) Disengage the 2 claws as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disengage the 3 clips to remove the center pillar lower garnish LH as shown in the illustration.

Remove in this Direction

13. REMOVE CENTER PILLAR UPPER GARNISH LH

(a) Using a clip remover, remove the 2 clips.

(b) Disengage the guide as shown in the illustration.

	Place Hand Here
	Remove in this Direction

Remove in this Direction

(d) Pass the anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

(e) Remove the clip from the center pillar upper garnish LH.

14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

(a) Disengage the claw as shown in the illustration.

Remove in this Direction

(b) Disengage the 2 claws and 3 guides as indicated by the arrows, in the order shown in the illustration to remove the roof side rail garnish assembly LH.

	Remove in this Direction (1)
	Remove in this Direction (2)

15. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 3 clips as shown in the illustration.

Remove in this Direction

(b) Disengage the guide to remove the roof side inner garnish LH as shown in the illustration.

Remove in this Direction

16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

20. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

22. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

23. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

24. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

25. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.

26. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

27. REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

28. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

29. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

for UA80E : Click here

for P710: Click here

30. REMOVE ROOF CONSOLE BOX ASSEMBLY

Click here

31. REMOVE SPOT LIGHT ASSEMBLY

Click here

32. REMOVE SENSOR COVER (w/ Humidity Sensor)

Click here

33. REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

Click here

34. REMOVE NO. 2 FORWARD RECOGNITION COVER

Click here

35. REMOVE NO. 1 FORWARD RECOGNITION COVER

Click here

36. REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip sub-assemblies.

(a) Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

SST: 09813-00010

NOTICE:

To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.

HINT:

Use the same procedure for the LH side and RH side.

Cutout

(b) Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

*a	30 to 45°
	Remove in this Direction

HINT:

Use the same procedure for the claw on the other side of the assist grip cover LH.
Use the same procedure for the LH side and RH side.

HINT:

Use the same procedure for the LH side and RH side.

(d) Disengage the 2 clips as shown in the illustration to remove the assist grip sub-assembly.

Remove in this Direction

(e) Remove the 2 clips from the vehicle body.

37. REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip sub-assembly.

38. REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip sub-assembly.

39. REMOVE VISOR BRACKET COVER LH

(a) Disengage the 4 claws and remove the visor bracket cover LH.

40. REMOVE VISOR ASSEMBLY LH

(a) for "TORX" Screw:

(1) Using a T25 "TORX" socket wrench, remove the 2 screws.

(b) except "TORX" Screw:

(1) Remove the 2 screws.

(c) Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.

*1	Visor Holder LH
	Remove in this Direction (1)
	Remove in this Direction (2)

(d) Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration.

(e) Disconnect the connector to remove the visor assembly LH.

41. REMOVE VISOR HOLDER LH

(a) Turn the visor holder LH approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.

*a	45°
*b	Base of the Visor Holder LH
	Remove in this Direction (1)
	Remove in this Direction (2)

(b) Disengage the 2 claws to remove the base of the visor holder LH.

42. REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.

43. REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

44. REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.

45. REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof)

(a) Remove the sun roof opening trim moulding.

46. REMOVE ROOF HEADLINING ASSEMBLY

(a) for Windshield Glass Side:

(1) Disconnect each connector.

(b) for Front Pillar LH Side:

(1) Remove the protective cover.

(2) Disconnect the 2 connectors.

(3) Using a clip remover, disengage the 4 clamps.

(4) Install the protective cover.

(1) Remove the protective cover.

(2) Remove the bolt.

*a	Guide
*b	Clamp

(3) Disengage the guide to disconnect the connector bracket.

(4) Using a clip remover, disengage the 2 clamps.

(5) Install the protective cover.

(d) for Rear Pillar LH Side:

(1) Disconnect the connector.

(2) Disengage the guide.

(e) for Rear Pillar RH Side:

(1) Disconnect each connector.

(2) Disengage the guide.

(f) for Roof Side (for Normal Roof):

(1) Slide the roof headlining assembly to disengage it from the 4 clips as shown in the illustration.

Remove in this Direction

HINT:

Leave the 4 clips installed to the vehicle body.

(g) for Roof Side (for Moon Roof):

(1) Disconnect the connector.

Remove in this Direction

(2) Slide the roof headlining assembly to disengage it from the 4 clips as shown in the illustration.

HINT:

Leave the 4 clips installed to the vehicle body.

(h) Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.

Remove in this Direction

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(i) Remove the 4 clips from the vehicle body as shown in the illustration.

Remove in this Direction

Instrument Panel Safety Pad

Ambient Light

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Audio And Visual System(for Gasoline Model): Panel Switches do not Function. Parking Brake Switch Circuit. Parts Location
Panel Switches do not Function CAUTION / NOTICE / HINT NOTICE: Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System. Click here When replacing the radio ...