Components
COMPONENTS
ILLUSTRATION
|
*A | for Gasoline Model |
*B | w/ Seat Heater System |
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
|
*A | for Gasoline Model |
*B | w/ Seat Heater System |
|
*1 | LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
|
*3 | REAR SEAT CUSHION ASSEMBLY |
*4 | REAR SEAT CUSHION LOCK HOOK |
|
● | Non-reusable part |
- | - |
ILLUSTRATION
|
*A | for Gasoline Model |
- | - |
|
*1 | CENTER PILLAR LOWER GARNISH |
*2 | FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY |
|
*3 | FRONT DOOR OPENING TRIM WEATHERSTRIP |
*4 | FRONT DOOR SCUFF PLATE |
|
*5 | FRONT SEAT OUTER BELT ASSEMBLY |
*6 | LAP BELT OUTER ANCHOR COVER |
|
*7 | REAR DOOR OPENING TRIM WEATHERSTRIP |
*8 | REAR DOOR SCUFF PLATE |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
|
*A | for HV Model |
- | - |
|
*1 | CENTER PILLAR LOWER GARNISH |
*2 | FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY |
|
*3 | FRONT DOOR OPENING TRIM WEATHERSTRIP |
*4 | FRONT DOOR SCUFF PLATE |
|
*5 | FRONT SEAT OUTER BELT ASSEMBLY |
*6 | LAP BELT OUTER ANCHOR COVER |
|
*7 | REAR DOOR OPENING TRIM WEATHERSTRIP |
*8 | REAR DOOR SCUFF PLATE |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
Inspection
INSPECTION
PROCEDURE
1. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
|
*a | Component without harness connected (Front Door Courtesy Light Switch Assembly) |
|
*b | Switch Body |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|
1 - Switch body | Not pushed (ON) |
Below 1 Ω |
|
Pushed (OFF) | 10 kΩ or higher |
If the result is not as specified, replace the front door courtesy light switch assembly.
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
(a) Connect the connector.
(b) Using a T30 "TORX" socket wrench, install the front door courtesy light switch assembly with the screw.
Torque:
6.3 N·m {64 kgf·cm, 56 in·lbf}
2. INSTALL CENTER PILLAR LOWER GARNISH
Click here 
3. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
Click here
4. INSTALL LAP BELT OUTER ANCHOR COVER
Click here
5. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
Click here
6. INSTALL REAR DOOR SCUFF PLATE (for Gasoline Model)
Click here
7. INSTALL REAR DOOR SCUFF PLATE (for HV Model)
Click here
8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
Click here
9. INSTALL FRONT DOOR SCUFF PLATE
Click here
10. INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here
11. INSTALL REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here
12. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here
13. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (for Gasoline Model)
w/ Seat Heater System:
Click here
14. INSTALL SPARE WHEEL COVER ASSEMBLY (for Gasoline Model)
w/ Seat Heater System:
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE SPARE WHEEL COVER ASSEMBLY (for Gasoline Model)
w/ Seat Heater System:
Click here 
2. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (for Gasoline Model)
w/ Seat Heater System:
Click here
3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here
4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here
6. REMOVE FRONT DOOR SCUFF PLATE
Click here
7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Click here
8. REMOVE REAR DOOR SCUFF PLATE (for Gasoline Model)
Click here
9. REMOVE REAR DOOR SCUFF PLATE (for HV Model)
Click here
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
Click here
11. REMOVE LAP BELT OUTER ANCHOR COVER
Click here
12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
Click here
13. REMOVE CENTER PILLAR LOWER GARNISH
Click here
14. REMOVE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
| (a) Using a T30 "TORX" socket wrench, remove the screw. |
|
(b) Disconnect the connector to remove the front door courtesy light switch assembly.
