Toyota Avalon (XX50): Glove Box Light

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Vehicle Interior / Lighting (int) / Glove Box Light

Components

COMPONENTS

ILLUSTRATION

GLOVE BOX LIGHT ASSEMBLY

LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Inspection

INSPECTION

PROCEDURE

1. INSPECT GLOVE BOX LIGHT ASSEMBLY

*a	Component without harness connected (Glove Box Light Assembly)

(a) Apply auxiliary battery voltage to the glove box light assembly and check that the light illuminates.

OK:

Measurement Condition	Specified Condition
Auxiliary battery positive (+) → 1 (B) Auxiliary battery negative (-) → 2 (L)	Glove box light illuminates

Measurement Condition

Specified Condition

Auxiliary battery positive (+) → 1 (B)

Auxiliary battery negative (-) → 2 (L)

Glove box light illuminates

If the result is not as specified, replace the glove box light assembly.

Installation

INSTALLATION

PROCEDURE

1. INSTALL GLOVE BOX LIGHT ASSEMBLY

(a) Turn the glove box light assembly as shown in the illustration to install it.

Install in this Direction

2. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Click here

3. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during glove box light assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
		Lighting system (for Gasoline Model with Cornering Light)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
		Lighting system (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for Gasoline Model:

Click here

for HV Model:

Click here

PROCEDURE

1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

2. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Click here

3. REMOVE GLOVE BOX LIGHT ASSEMBLY

(a) Turn the glove box light assembly as shown in the illustration to remove it.

Remove in this Direction

Front Door Courtesy Switch

Inside Handle Light

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Power Outlets (int): Power Outlet Socket(for Console Box Front Side)
ComponentsCOMPONENTS ILLUSTRATION *1 USB CHARGER SOCKET - - InstallationINSTALLATION PROCEDURE 1. INSTALL USB CHARGER SOCKET (a) Engage the 4 claws to install the USB charger socket as shown in the illustration. Install in this Direction (b) Connect the connector. 2. INSTALL CONSOLE BOX ASSEMBLY Cl ...