Components
COMPONENTS
ILLUSTRATION
|
*1 | SPARE WHEEL COVER ASSEMBLY |
- | - |
ILLUSTRATION
-
|
*A | for Gasoline Model |
*B | for HV Model |
|
*1 | LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
|
*3 | REAR SEAT CUSHION ASSEMBLY |
*4 | REAR SEAT CUSHION LOCK HOOK |
|
● | Non-reusable part |
- | - |
ILLUSTRATION
|
*A | for Gasoline Model |
- | - |
|
*1 | BENCH TYPE REAR SEAT CUSHION COVER |
*2 | CHILD RESTRAINT SEAT BASE COVER |
|
*3 | CHILD RESTRAINT SEAT COVER |
*4 | REAR SEAT CUSHION HEATER ASSEMBLY |
|
*5 | REAR SEAT CUSHION PAD SUB-ASSEMBLY |
*6 | HOG RING |
|
*7 | TAG PIN |
- | - |
|
● | Non-reusable part |
- | - |
ILLUSTRATION
|
*A | for HV Model |
- | - |
|
*1 | BENCH TYPE REAR SEAT CUSHION COVER |
*2 | CHILD RESTRAINT SEAT BASE COVER |
|
*3 | CHILD RESTRAINT SEAT COVER |
*4 | REAR SEAT CUSHION HEATER ASSEMBLY |
|
*5 | REAR SEAT CUSHION PAD SUB-ASSEMBLY |
*6 | HOG RING |
|
*7 | TAG PIN |
- | - |
|
● | Non-reusable part |
- | - |
Inspection
INSPECTION
PROCEDURE
1. INSPECT REAR SEAT CUSHION HEATER ASSEMBLY (for LH Side)
| (a) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
A-1 - K57-2 | Seat heater temperature 23 °C (73 °F) |
4.61 to 5.64 Ω | |
A-1 - K57-1 | Seat heater temperature 23 °C (73 °F) |
4.61 to 5.64 Ω | |
A-2 - K57-2 | Always |
Below 1 Ω | If the result is not as specified, replace the rear seat cushion heater assembly. |
 |
|
*a | Component without harness connected
(Rear Seat Cushion Heater Assembly) | | |
2. INSPECT REAR SEAT CUSHION HEATER ASSEMBLY (for RH Side)
| (a) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
C-1 - K58-2 | Seat heater temperature 23 °C (73 °F) |
4.61 to 5.64 Ω | |
C-1 - K58-1 | Seat heater temperature 23 °C (73 °F) |
4.61 to 5.64 Ω | |
C-2 - K58-2 | Always |
Below 1 Ω | If the result is not as specified, replace the rear seat cushion heater assembly. |
 |
|
*a | Component without harness connected
(Rear Seat Cushion Heater Assembly) | | |
Installation
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the seat frame may injure your hands.
PROCEDURE
1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY
(a) Install the rear seat cushion heater assembly to the bench type rear seat cushion cover with 19 new tag pins.
2. INSTALL BENCH TYPE REAR SEAT CUSHION COVER
Click here
3. INSTALL CHILD RESTRAINT SEAT BASE COVER
Click here
4. INSTALL CHILD RESTRAINT SEAT COVER
Click here
5. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
6. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here
7. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
8. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
9. INSTALL SPARE WHEEL COVER ASSEMBLY
Click here
10. CHECK SEAT HEATER
for HV Model:
Click here
for Gasoline Model:
Click here
Removal
REMOVAL
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. REMOVE SPARE WHEEL COVER ASSEMBLY
Click here
2. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD
Click here
3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
4. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
6. REMOVE CHILD RESTRAINT SEAT COVER
Click here
7. REMOVE CHILD RESTRAINT SEAT BASE COVER
Click here
8. REMOVE BENCH TYPE REAR SEAT CUSHION COVER
Click here
9. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY
| (a) Remove the 19 tag pins and rear seat cushion heater assembly from the bench type rear seat cushion cover.
HINT: Use the same procedure for the RH side and LH side. |
|
